[[email protected]]

Welded Push Bar. The main frame is 2" x 4" tubular steel. The headlight guards are 1" x 2" tubular steel and are heavily bolted onto the main frame. This bar was originally made for a 2005 Dodge Dakota ST. The mounts ran through the bumper valances and mounted to two 1/4" plates bolted 3 times to the back of the bumper mount. Very sturdy, very bold, very heavy. Currently roughly painted, could use a repaint or just another coat of primer. Located Commerce, Michigan. Since I sold the truck, I have really no way to transport it. Asking $100 for the bar and mounts.

Bar on my truck. Rubber ducky not included!

Another angle. Again, Rubber ducky not included!

mount plates

where they mount

 

[[email protected]]

bump

 

[[email protected]]

bump

 

[03hemisilver]

What guage is the chain? Just want to make sure it's sturdy enough to support an impact?

 

[unclebeaner]

how much for the duck?

 

[clarkstoncracker]

I'm interested, but I'm curious if I could still drive through car washes with it on there. Any experience with that?

 

[95geo]

would you be interested in building me one for my jeep compass? I want something just like that except around the winshield and mirrors. would you be interested in taking a look at it some time?

 

[jeeperstrudie]

Pretty sweet!!!!! I especially love the look, that the chains add to it!!! Could you make one of these for my wifes Impala? How are the chains connected? Are they pretty secure? I was thinking I could use them to handcuff the wife to when she gets in one of her Dirty nasty slutty moods - HOT!!!!! and if I get pissed at her then I could just jump in and go for a ride.

 

[KartRacer]

If you were to include the rubber ducky, it would already be sold.

Can I get a close up pic of the welds?

 

[84ramcharger]

Would this fit on a YJ?

 

[Pokerob]

man that thing is titties and beer all day long!

 

[diesels77]

Would this fit on a YJ?

Sure, see the square headlight holes.oke:

 

[[email protected]]

What guage is the chain? Just want to make sure it's sturdy enough to support an impact?

It's about 3/8 thick links and welded to the headlight guards. I bet you could tow with them.

 

[[email protected]]

Would this fit on a YJ?

Acetylene torch and some measurements no problem. (the torch is for the bumper)

 

[[email protected]]

Pretty sweet!!!!! I especially love the look, that the chains add to it!!! Could you make one of these for my wifes Impala? How are the chains connected? Are they pretty secure? I was thinking I could use them to handcuff the wife to when she gets in one of her Dirty nasty slutty moods - HOT!!!!! and if I get pissed at her then I could just jump in and go for a ride.

Yes I could make one for an impala, but probably not for what you're looking to do with it.

 

[[email protected]]

I'm interested, but I'm curious if I could still drive through car washes with it on there. Any experience with that?

It's hit or miss. I go through most of the local washes without a problem. Though it's obviously an "aftermarket item", they're more worried about their car wash than the bumper. Never had a problem in a car wash.

 

[[email protected]]

If the duck will make the sale, I guess I'll put it back on and sell it with the bumper??

 

[SlayerXJ]

I hope you noticed all the helpful tags people added haha

 

[[email protected]]

would you be interested in building me one for my jeep compass? I want something just like that except around the winshield and mirrors. would you be interested in taking a look at it some time?

Sure. Dryden is out there a bit from where I live but if you're really interested I have made two other custom bars and a rear bumper/trailer hitch for friends. Takes me a few hours to measure stuff out but it's a possibility.

 

[[email protected]]

bump