[cyrus]

***SOLD***
1990 XJ, no doors or any sheet metal above window line.
chassis is bare
long arm front brackets, (3 link, upper frame end needs attention)
4 link double tri rear brackets
sub frame plated and additional cross members
full cage, 1 3/4 x .120 DOM with integrated seat mounts 1 1/4 x .120 DOM
Rocker Slides 1 3/4 x .120 DOM
half doors ( not sure if they will fit up any more....
500$


***SOLD***
4 nearly new, 36 13.5 Irock bias on 15x10 (5x5.5 4" BS) steel (chrome) wheels
very little use on 4 (90+%) one has a small cut in the side wall, not to deep to damage, but enough to notice.
1 spare, not new.
850$


***SOLD***
1990 NP231-J (21 spline input installed, 23 spline included) w/AA SYE, this is not the supershort version, it has the speedo gear drive. (part# np231-sye)
175$


***SOLD***
XJ Steering Box 4 years old. lightly used
West Texas Offroad Re-manufactured and ported for Hydraulic assist
175$

***SOLD***
Front double cardan drive shaft, 1310 joints, 31-33.5 long
Rear double cardan drive shaft, 1310 joints, 32-36 long
$50 each



***SOLD***
D44 HP, 5 on 5.5, 5.13 Precision Gear R&P, Eaton E-locker with wiring
62.5 WM 2 WM
Chevy High Steer Knuckles
Moser Chomo inner and outers
Warn Premium lock outs
West Texas Hyd Assist Ram
Trussed
not full width
1150$

***SOLD***
Shorty Winch Bumper
1 3/4 x .120 DOM
140$


***SOLD***

1990 AW4 21 spline output, could maybe use a pump otherwise is in great working order.
50$

***SOLD***
9", 5 on 5.5, 5.13 Precision Gear R&P, Strange 33spline Spool
61" WM 2 WM
Disc brake conversion
Moser Chromo's
not full width
450$








if interested in anything, please pm me, i will check most nights.
if you want pictures, please PM with an email address. I will send you pics of what you want to see.

No Trades, cash, money transfer.
I will ship, but at your cost.

 

[sleeperd2]

Interested in 231 w/AA short SYE. Can you send pics
[email protected]

 

[cyrus]

ttt

 

[kmanxj5011]

are the rock sliders rocker replacements or bolt ons?

 

[cyrus]

custom. they are part of the cage and sub frame added to the chassis.

I may be able to cut the cage apart from the sliders, and cut the mounts to the frame, but you would be left with substantial fabrication to install them on your vehicle.

I am willing to do so, but after I know no one wants the complete chassis. I am pulling that sale in two weeks if not sold, then the entire chassis is going to the recycler.

 

[kmanxj5011]

custom. they are part of the cage and sub frame added to the chassis.

I may be able to cut the cage apart from the sliders, and cut the mounts to the frame, but you would be left with substantial fabrication to install them on your vehicle.

I am willing to do so, but after I know no one wants the complete chassis. I am pulling that sale in two weeks if not sold, then the entire chassis is going to the recycler.

can you post or pm me some pics? If it comes down to that i may be still be interested in them pending on what they look like and maybe some pieces of the cage. Thanks

 

[cyrus]

whats your email address? i seem to have issues getting the pic to post...

 

[kmanxj5011]

pm sent

 

[cyrus]

ttt

 

[cyrus]

:drink:

 

[GREASYHANDS]

How much for one of the front cardan shafts? Can I get a extended and collapsed measurment?

 

[cyrus]

i'll measure it tomorrow.

the slip is very tight, due to lack of length cycle on the front DS. it will move, its just very tight.


I was asking 100 for the both, so fifty each.

 

[cyrus]

How much for one of the front cardan shafts? Can I get a extended and collapsed measurment?

Rear
32-36
3" tube.

Front
31-33.5
2" tube.

1310 joints.

 

[cyrus]

ttt

 

[cyrus]

bump

 

[cyrus]

bump

 

[cyrus]

ttt

 

[cyrus]

price drop.

somebody should be able to put these to a very good use....

 

[cyrus]

the 44 is sold,

who wants the 9"?

 

[cyrus]

9" still available.