Great Lakes 4x4. The largest offroad forum in the Midwest banner
sbc
1-10 of 11 Results
  1. Completed Sales
    CJ-7 with 350 SBC. Headers, edelbrock intake, RV cam, holley 600 carb, th350 trans, 205 t-case, ratchet shifter, K5 Blazer Axles, hard top, steel doors, BFG's. Tons of extras - extra doors, winch bumper (not pictured), new windshield (not pictured), extra body parts, extra t-case. Also...
  2. Vehicles for sale
    93 4 door 35 in tires decent life left sbc 350 edelbrock carb with edelbrock intake s10 v8 headers dual mufflers power windows b&m shifter hei distributor 2800rpm sta torque converter ORD soa with solid axle conversion dana 30 and ford 8.8 rear disc. Runs drives sounds great very loud very fast...
  3. Parts for sale
    I have a running sbc 355 (350 bored .30 over....remanufactured motor) 4 barrel edelbrock carb, alum intake. headers and more txt 7345454864 -jared 450.00 obo
  4. Completed Sales
    I have a set of Sanderson CS13 S-10 Small Block Chevy conversion headers. 1 3/4" primary tube and 3" collector. Brand new high temperature gray powder coating. They are 2wd headers but I used them on my 4wd truck and only had to trim the top corner of the drivers side shock mount. I used them...
  5. Parts for sale
    I have 4 35-16.5-15 on 8 lug steel 12" wide wheels. 85% Tread, a little fender rash, nothing structural or chunking damage. $750 or trade.... lookinf for: Cut boggers or hawgs. 35-36 range ... SBC intake for 4500 Dominator Carb.... Good Predator Carb Suspension seats (mastercraft etc...)...
  6. Completed Sales
    I've got a 355 small block Chevy engine that has been rebuilt. Bored .030" over, flat top pistons, Crane fireball cam, 194 heads, and an Edelbrock performer intake. All new gaskets and seals, one new freeze plug (old one was leaking from the improper previous installation, the motor hasn't...
  7. Parts for sale
    Early 1970s recently rebuilt small block chevy v8 307cid .030 over. Rebuilt approx 2 years ago and not use very often, runs great and sounds great. Rebuild included - new crank, all bearings, gaskets, rings, machine work, timing set, high volume oil pump, Edelbrock EPS intake, Edelbrock TBI...
  8. General Tech
    I have a 1969 350 4-bolt that has been bored 0.060" over. It has around 9-9.5:1 compression (used an online calculator) aluminum intake, centre dump manifolds, attached to a TH350/231C HD in my heep. It has a HUGE POS cam in it (I will be changing it to this...)...
  9. Parts for sale
    I have for sale: -5.7(350) block , bored .40 over. Bare. Needs to be honed. That's all!---$25.00 -350 crank. Freshly machined at Baldwin Auromotive! Paid $120.00.---$100.00 -350 comp cam .425 lift with matching litters!!---$50.00 -SBC Flat top .40 over pistons a with reconditioned rods (with...
  10. Parts for sale
    I have a 305, needs a starter has an edelbrock 1406 and a spacer, and HEI ignition. Good 700r4 w/ convertor, bolted up to a np208, still has the brace attached. $350 takes all Price drop $300 takes it all Will trade for a SBC maybe modified 350, or low mileage stock one bigger than a 305...
1-10 of 11 Results
Top