Looking for a 14 bolt with 4.10 gears and 8/6.5 lug pattern. also looking for a Driver side drop front axle. big hub 44 or 60 that has same lug pattern. will buy as a set or separate. Nothing special as i dont really want to spend a lot of money.
New unused Advance Adapter GM Turbo 400 to Jeep Dana 300.
Going a different route.
I have two axles for sale.
Both pulled out of a 2007 Jeep Wrangler Sahara Unlimited. Decided to upgrade for the 4BT swap.
- Dana 44 rear with 5.38s (I have the stock 4.10s available, ABS lines cut)
- Dana 30 front with 4.10s (busted Spartan auto locker but still drivable, no ABS lines on it)...
dana 70 hd dually axle srw and disc brake conversion.
Axle housing and all brake components with new bearings in hubs $250
Dana 70 hd master overhaul kit form east coast gear supply $150
located in lake orion call or text Evan at 248-760-4417
Dana 44 Front out of J10: 3.54 gears; Disk; 6 lug; Passenger drop; Complete;
Dana 44 Rear out of J10; 6 lug; no carrier or ring/pinion; no backing plates; 4" offset;
AMC 20 Narrow Track: Fully rebuilt with minimal milage; no drums; 3.54 gears;
AMC 20 Quadratrac: No backing plate or brakes; 3.54...
I have a stock jeep tj rear AXLE, from a 6 cyl i believe. Got with a set i bought, not going to use this.
3.73 axle ratio think it is a dana 35, what ever was stock in the tj 6 bangers...
Drum to drum
250.00 or best, make offer.
this is the link to a 4x4 website with the kit.
this set up was under a high school girls tj for...
I have a Dana 60 out of a 1979 Ford F250 (with snow fighter package)
4.10 gears with factory limited slip
The wms (wheel mounting surface) width is stock about 66"
30 spline shafts
Has drums but no other brake components.
I bought the axle to put under my jeep but decided to go...
Figured I would throw this on here. Most people are looking for a wheeler and this might be a little out of the price range for a budget build, but its a solid runner for someone looking for a DD or a not rusted out low mileage wheeler project. Slight valve cover leak, other than that its SOLID...
Set if Ford f250 axles front and rear. The front is a Dana 44 the rear is a Dana 60 full float. Pretty sure the ratio is 411. Call or text john at 989 928 2223. Asking 400 for the set or open to trades.
I have a Dana 35 that came out of a Yj. It has 4.56 gears, Detroit locker, and a weird disc brake conversion done by the previous owner of the axles. new brake pads, brake lines, axle seals and pinion seal. have spare shafts out of my old axles.
Have the matching front Dana 30, Posi or a...
Both Front and Rear JK Rubicon Dana 44 axles for sale.
OEM electric lockers and 4:10 gears
OEM brackets and tabs
Include ARB differential covers, and locker switch.
Less than 6,000 miles on them, never broken or damaged.
And because I have an extra set, they include the Synergy Suspension...
i need to know what would be a good axle swap for my 93 yj, currently running 4.10s, dana 30/35 but changing to 3.73s
already have a front axle lined up,,... (hamydown)
good for the price, strength, reliability, and ease of getting
My rear differential cover is dripping (D35) on my '93 Wrangler
I'm wondering what I should use to seal it
I've seen posts about how RTV works fine, but a gasket is the right way to do it
I'm just looking for some advice, maybe based on prior experience or knowledge
Has anyone ever used a Dana 18 to make a 2 speed rear end.
Basically you would flip it 90 degrees upright making the drive shaft's ends upright.
Then turn it 180 sideways making the input the new output going into the rear axle.
The rear end end of the drive shaft would come up to the rear...