rugrat the sloppy-xj - Page 3 - Great Lakes 4x4. The largest offroad forum in the Midwest

ulimate fighter · March 24th, 2018, 10:24 AM

sterlingfire · March 24th, 2018, 03:17 PM

keep going, it's looking good!

ulimate fighter · March 25th, 2018, 07:46 AM

Got a complete hub to hub dana 50 from an excursion for $100

ulimate fighter · May 10th, 2018, 07:37 PM

i've got a passenger seat! Driver floor is still getting there

ulimate fighter · December 1st, 2018, 04:26 PM

JohnnyJ · December 2nd, 2018, 07:35 AM

Nice tin work.

Sent from my SM-T710 using Tapatalk

ulimate fighter · December 8th, 2018, 01:52 PM

Thank you sir!

CheapThrillB2 · December 9th, 2018, 10:30 AM

I like the floor board work. Clean. Hate doing that kind of work.

Carefully with that 205 mount. Puts funny stress on the tcase adapter and trans housing having a mount there and one in the center of the adapter. Seen a few adapters and trans housing crack. I prefer to support the 205 at the adapter and under the rear output.

Is the exhaust gonna clear the frt driveshaft at bump?

CheapThrillB2 · December 9th, 2018, 10:37 AM

Am I the only one thats only seeing pics from the last couple posts?

ulimate fighter · February 14th, 2019, 10:46 PM

My photos got corrupted. When I post from Facebook they only last a few months.

As for the 205 I planned a brace for the PTO side just haven't got the drawing sent of to water jet yet.

Did some stuff. Maybe a few weeks away from startup. Running and driving shortly after

ulimate fighter · February 19th, 2019, 09:03 PM

Wiring, fuel, and plumbing and it'll run

green50gt · February 20th, 2019, 08:48 AM

Where are you in Bristol?

ulimate fighter · February 21st, 2019, 04:58 PM

Cr17 and cr6

green50gt · February 22nd, 2019, 10:30 AM

Quote:

Originally Posted by ulimate fighter

Cr17 and cr6

That's Bristol all the way over there? huh. Well I guess 6 span is considered Bristol isn't it?

I bought a 405k 2wd 2 door XJ near there a number of years ago. Nice area.

jbsjunk · February 22nd, 2019, 11:23 AM

Quote:

Originally Posted by ulimate fighter

22x19x3"

Quote:

Originally Posted by JohnnyJ

Will be interesting to see how it cools with your horsepower goals. I had good luck with stock LQ4 and a 24x19, but it struggled with heads and a cam.

My SBC does time with this once I figured out the pulley ratio.

ulimate fighter · May 19th, 2019, 02:29 PM

It runs and drives I have to work out some bugs. I think my iat sensor is not reading right and it's pig rich. Still wants to spin in every gear.

Need to build the front shaft and get the door hinges figured out. I had to cut them off because the torx were stripped and the pins were rusted.

After that I'll put some street miles on it then hit some terrain.

I've got to figure out how to post videos from my phone or dig my GoPro out

ulimate fighter · May 27th, 2019, 09:58 PM

http://m.youtube.com/watch?v=LYdZbOQ9nPg

green50gt · May 28th, 2019, 08:55 AM

C.R. 17!! Cool, do some peel outs!

ulimate fighter · June 2nd, 2019, 09:21 PM

I've been terrorizing my neighbor Hood with what I call "jeepkana"

December 2nd, 2018, 07:35 AM	#46
JohnnyJ Low Range Drifter Join Date: 11-09-05 Location: Hartland, MI Posts: 7,954 iTrader: (38) Mentioned: 87 Post(s)	Nice tin work. Sent from my SM-T710 using Tapatalk __________________ Surviving Project Car Hell Buggy build

February 14th, 2019, 10:46 PM	#50
ulimate fighter king-dingaling Join Date: 01-11-14 Location: Bristol Posts: 63 iTrader: (0) Mentioned: 0 Post(s)	My photos got corrupted. When I post from Facebook they only last a few months. As for the 205 I planned a brace for the PTO side just haven't got the drawing sent of to water jet yet. Did some stuff. Maybe a few weeks away from startup. Running and driving shortly after Attached Thumbnails

February 19th, 2019, 09:03 PM	#51
ulimate fighter king-dingaling Join Date: 01-11-14 Location: Bristol Posts: 63 iTrader: (0) Mentioned: 0 Post(s)	Wiring, fuel, and plumbing and it'll run Attached Thumbnails

February 20th, 2019, 08:48 AM	#52
green50gt Got rocks? Join Date: 04-16-08 Location: Goshen, IN 46528 Posts: 3,824 iTrader: (63) Mentioned: 11 Post(s)	Where are you in Bristol? __________________ I heart Jeeps

May 19th, 2019, 02:29 PM	#56
ulimate fighter king-dingaling Join Date: 01-11-14 Location: Bristol Posts: 63 iTrader: (0) Mentioned: 0 Post(s)	It runs and drives I have to work out some bugs. I think my iat sensor is not reading right and it's pig rich. Still wants to spin in every gear. Need to build the front shaft and get the door hinges figured out. I had to cut them off because the torx were stripped and the pins were rusted. After that I'll put some street miles on it then hit some terrain. I've got to figure out how to post videos from my phone or dig my GoPro out Attached Thumbnails

March 24th, 2018, 10:24 AM	#41
ulimate fighter king-dingaling Join Date: 01-11-14 Location: Bristol Posts: 63 iTrader: (0) Mentioned: 0 Post(s)

March 24th, 2018, 03:17 PM	#42
sterlingfire Senior Member Join Date: 08-11-14 Location: sterling, not sterling heights... Posts: 699 iTrader: (3) Mentioned: 3 Post(s)	keep going, it's looking good!

March 25th, 2018, 07:46 AM	#43
ulimate fighter king-dingaling Join Date: 01-11-14 Location: Bristol Posts: 63 iTrader: (0) Mentioned: 0 Post(s)	Got a complete hub to hub dana 50 from an excursion for $100

May 10th, 2018, 07:37 PM	#44
ulimate fighter king-dingaling Join Date: 01-11-14 Location: Bristol Posts: 63 iTrader: (0) Mentioned: 0 Post(s)	i've got a passenger seat! Driver floor is still getting there

December 1st, 2018, 04:26 PM	#45
ulimate fighter king-dingaling Join Date: 01-11-14 Location: Bristol Posts: 63 iTrader: (0) Mentioned: 0 Post(s)

December 8th, 2018, 01:52 PM	#47
ulimate fighter king-dingaling Join Date: 01-11-14 Location: Bristol Posts: 63 iTrader: (0) Mentioned: 0 Post(s)	Thank you sir!

December 9th, 2018, 10:30 AM	#48
CheapThrillB2 FAWK YEAH!! Join Date: 09-06-06 Location: Middleville, MI Posts: 36,068 iTrader: (67) Mentioned: 80 Post(s)	I like the floor board work. Clean. Hate doing that kind of work. Carefully with that 205 mount. Puts funny stress on the tcase adapter and trans housing having a mount there and one in the center of the adapter. Seen a few adapters and trans housing crack. I prefer to support the 205 at the adapter and under the rear output. Is the exhaust gonna clear the frt driveshaft at bump?

December 9th, 2018, 10:37 AM	#49
CheapThrillB2 FAWK YEAH!! Join Date: 09-06-06 Location: Middleville, MI Posts: 36,068 iTrader: (67) Mentioned: 80 Post(s)	Am I the only one thats only seeing pics from the last couple posts?

February 21st, 2019, 04:58 PM	#53
ulimate fighter king-dingaling Join Date: 01-11-14 Location: Bristol Posts: 63 iTrader: (0) Mentioned: 0 Post(s)	Cr17 and cr6

May 27th, 2019, 09:58 PM	#57
ulimate fighter king-dingaling Join Date: 01-11-14 Location: Bristol Posts: 63 iTrader: (0) Mentioned: 0 Post(s)	http://m.youtube.com/watch?v=LYdZbOQ9nPg

May 28th, 2019, 08:55 AM	#58
green50gt Got rocks? Join Date: 04-16-08 Location: Goshen, IN 46528 Posts: 3,824 iTrader: (63) Mentioned: 11 Post(s)	C.R. 17!! Cool, do some peel outs! __________________ I heart Jeeps

June 2nd, 2019, 09:21 PM	#59
ulimate fighter king-dingaling Join Date: 01-11-14 Location: Bristol Posts: 63 iTrader: (0) Mentioned: 0 Post(s)	I've been terrorizing my neighbor Hood with what I call "jeepkana"

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
XJ stock rear drive shaft	58-fc170	Wanted	0	January 4th, 2017 10:55 AM
XJ parts leftovers	0Toncaddy	Parts for sale	4	January 27th, 2016 11:52 AM
Misc Jeep Part(s) (7) Jeep Cherokee (XJ) driveshafts	1x1_Speed_Craig	Parts for sale	21	February 19th, 2015 05:36 AM
Maeve's 2000 XJ 2-door Sport build (Mira's li'l sister)	1x1_Speed_Craig	Rig Builds and Pics	6	January 2nd, 2015 05:58 PM
231 sye, xj auto front d/s, xj rear driveshaft	Cubbetm	Wanted	0	September 11th, 2014 06:06 PM