Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Toyota Tech
GL4x4 Live! GL4x4 Casino







Search
Reply
 
Thread Tools
Old July 7th, 2007, 11:45 AM   #1
BOGDOG
Senior Member
 
BOGDOG's Avatar
 
Join Date: 11-11-06
Location: White Lake/Wixom
Posts: 2,189
iTrader: (7)
Drag Link rebuild

The steering on my 85 4runner is getting a little sloppy. I ordered a drag link rebuild kit. I have an 80 axle laying around and figured I would try to take it apart to see what I was in for before I tear into my daily driver. It looks like I am going to need a giant straight bladed screwdriver to take this apart. Has anybody rebuilt a drag link on a yota?
BOGDOG is offline   Reply With Quote
Old July 7th, 2007, 03:00 PM   #2
Haggar
Covered in mud...
 
Haggar's Avatar
 
Join Date: 11-06-05
Location: Oxford, MI
Posts: 17,376
iTrader: (52)
I've only taken them apart. Yeah, its like a 3/4" wide screw. Mines all hi-steer now...
Haggar is offline   Reply With Quote
Old July 7th, 2007, 03:40 PM   #3
skife
Senior Member
 
skife's Avatar
 
Join Date: 02-12-07
Location: cedar springs mi
Posts: 5,052
iTrader: (5)
Send a message via AIM to skife Send a message via MSN to skife
will that axle from the 80 fit on my 92?
skife is offline   Reply With Quote
Old July 7th, 2007, 09:44 PM   #4
BOGDOG
Senior Member
 
BOGDOG's Avatar
 
Join Date: 11-11-06
Location: White Lake/Wixom
Posts: 2,189
iTrader: (7)
I think the solid front axles are all about the same except the later ones have a beefier housing. I am taking it apart for spares.
BOGDOG is offline   Reply With Quote
Old July 7th, 2007, 10:46 PM   #5
Buggy_Tim
(513) 891-8372
 
Buggy_Tim's Avatar
 
Join Date: 11-05-05
Location: Sault Sainte Marie
Posts: 11,605
iTrader: (12)
You'll also need heat to get that screw out. Hate those things. I have a giant flat blade looking socket that goes on a 1/2 drive ratchet or impact. I usually adapt it down to 3/8 and use my 3/8 impact to get them apart.
Buggy_Tim is offline   Reply With Quote
Old July 9th, 2007, 10:49 AM   #6
incogrhino
i pull out
 
incogrhino's Avatar
 
Join Date: 09-11-06
Location: ravenna
Posts: 465
iTrader: (1)
Take care of that thing, mine cost me a tire when my seperated and put the pitman arm threw my side wall.
incogrhino is offline   Reply With Quote
Old July 9th, 2007, 11:31 AM   #7
BOGDOG
Senior Member
 
BOGDOG's Avatar
 
Join Date: 11-11-06
Location: White Lake/Wixom
Posts: 2,189
iTrader: (7)
It wasn't so bad. Took spare one apart to see how it worked then took one off of 4Runner. Had to use spare drag link as one of the sockets was siezed in the one off of 4Runner. The worst part was getting cotter pins out of spare one. I stopped at the tool barn on M59 near Howell and he had a 1/2" drive screwdriver bit that fit perfect. I'll have to throw that in my Toy tool kit with the 54mm snap on socket I had to buy to do the wheel bearings. No heat no bfh. It definately tightened up my steering.
BOGDOG is offline   Reply With Quote
Old July 9th, 2007, 03:47 PM   #8
incogrhino
i pull out
 
incogrhino's Avatar
 
Join Date: 09-11-06
Location: ravenna
Posts: 465
iTrader: (1)
I wonder if it's possible to find a different part with maybe a hex(allen) in it instead of the slot.I'll hafta look next time I'm at the hardware store.Matchin the tread would be the only hard part.hmmmmm....
incogrhino is offline   Reply With Quote
Old July 9th, 2007, 09:46 PM   #9
Buggy_Tim
(513) 891-8372
 
Buggy_Tim's Avatar
 
Join Date: 11-05-05
Location: Sault Sainte Marie
Posts: 11,605
iTrader: (12)
Quote:
Originally Posted by incogrhino View Post
I wonder if it's possible to find a different part with maybe a hex(allen) in it instead of the slot.I'll hafta look next time I'm at the hardware store.Matchin the tread would be the only hard part.hmmmmm....
now that's an idea....but that would be a damn big allen bolt...like a huge ass set screw.
Buggy_Tim is offline   Reply With Quote
Old July 10th, 2007, 03:22 PM   #10
incogrhino
i pull out
 
incogrhino's Avatar
 
Join Date: 09-11-06
Location: ravenna
Posts: 465
iTrader: (1)
yep, I just hate the slot.That and maybe in 20 years I could actually get it apart again.Ahhh, but with out the slot, there is no where to run the cotter pin threw.hmmmm...
incogrhino is offline   Reply With Quote
Old July 10th, 2007, 06:22 PM   #11
Buggy_Tim
(513) 891-8372
 
Buggy_Tim's Avatar
 
Join Date: 11-05-05
Location: Sault Sainte Marie
Posts: 11,605
iTrader: (12)
Cotter pin? Ones I worked on didn't have a cotter pin. Maybe that's why they were all f-ed up.:tonka:
Buggy_Tim is offline   Reply With Quote
Old July 11th, 2007, 11:40 AM   #12
BOGDOG
Senior Member
 
BOGDOG's Avatar
 
Join Date: 11-11-06
Location: White Lake/Wixom
Posts: 2,189
iTrader: (7)
You could always drill thru the new part for the cotter pin. I really had no problem with the slot and truck is 22 years old. I would not want to do it without the 1/2" drive bit. I used anti-sieze when I put it back together. I don't think it has been in Mi that long. It was clean and kinda low miles 92K when I bought it 4 years ago. I had to take drivers seat out last night it went from being one of the most comfortable to an backache pretty quick. All of the welds were broken on the parts that the pivot brackets bolt to on the upper part. I don't think I have to worry about that after I welded it back up. I think it is telling me to lose some weight. Have to take it back out though it will not recline now and my head is in the roof.
BOGDOG is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Toyota Tech
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -5. The time now is 10:38 AM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
Copyright 2005 - 2012 Cracker Enterprises - Powered by Linux
vB Ad Management by =RedTyger=
Page generated in 0.13462 seconds with 36 queries