1991 Wrangler YJ 350 Project - Great Lakes 4x4. The largest offroad forum in the Midwest

Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > Great Lakes 4x4 Marketplace > Vehicles for sale
GL4x4 Live! GL4x4 Casino

greatlakes4x4.com is the premier Great Lakes 4x4 Forum on the internet. Registered Users do not see the above ads.
Search
Reply
 
Thread Tools Search this Thread
Old May 19th, 2014, 04:53 PM   #1
Meltdown91
Newbie
 
Meltdown91's Avatar
 
Join Date: 03-25-13
Location: Decatur, IN
Posts: 19
iTrader: (0)
Mentioned: 0 Post(s)
Default 1991 Wrangler YJ 350 Project

I have '91 Jeep Wrangler! Don't let the pictures fool you It's definitely a Wrangler. The front clip is off an old CJ (not sure what year.) Both the body and frame are 100% Solid (there maybe a tiny bit of surface rust) but absoltley no rot, overall in amazing condition.

NOTE: HARD TOP AND FULL HARD DOORS NOT INCLUDED! COMES WITH GUTTED LOWER HARD DOORS, UPPER SOFT DOORS, AND BEST TOP REPLACE A TOP.

Now on to the goodies:

-Has a 81 K20 5.7l 350 C.I. (ran when I bought it to put in the Jeep, was more for mock up, I think it needs a rear main.)
-Motor mounts are "Advance Adapters" brand
-3 core all aluminum Champion radiator
-Brand new MSD Distributor
-Transmission is a SM465 Granny Gear 4 Speed (First gear is 6.55:1)
-Transfer case is a NP205, gear driven, has all new seals.
-Front axle is a full length 8 lug Corp. 10 bolt (Identical to a Dana 44)
-Rear axle is a full length 8 lug Corp. 14 bolt FF (holds it's own with a dana 60)
-14 Bolt has disk brake swap brackets

Both front and rear axles need pinion angle adjusted. Which is nothing if you know what your doing.

-Has 5.5 inch SOA (spring over axle) lift
-Brand new leaf springs
-Comes with a 20 gallon poly gas tank as well as the skid plate.
-Brand new Painless Performance wire harness! 800 bucks brand new!!!
-Brand New Windshield frame, windshield and seals, 300 bucks and installed by a professional!

Now onto the NOT so goodies:
Things it will need

-Brakes
-Brake lines plumbed
-Fuel lines plumbed
-Fuel pump
-Front engine Accessory Belt Drive
-Wiring needs finished
-Speedometer and Tachometer
-Drive shafts
-Plugs and wires
-Finish welds
-Shocks
-and Steering

And some good ol' TLC

This has been my project for some time now I'm loosing interest now that I bought my 94 Wrangler. I have a few thousand dollars invested over what I'm asking for. The Frame and tub alone are worth a little more than half, not to mention the placement for the motor and drive train is all ready figured so you have no guess work! I have nearly every receipt for almost ever part I have bought. It has title. I would make a hellasious trail rig, bogger, or even with some extra love a retired show vehicle! (be that your wish) If interested Text me "Braden" at (260) 2 two 3 - eight 3 five 9

I would like to get 2000 but I can be flexible. I would trade for a crotch rocket 600 cc to 800 cc motor, preferably honda but I'm not too picky, and must be no older than late 90's, also like cruisers, or an F250/ 2500 or??? Let me know what you got don't low ball me, I know what I have, I DON'T HAVE TO SELL. The frame and tub are worth half the asking price alone not to mention the carb, distributor, radiator, Painless wire harness, etc!

Thanks for looking!
Braden
Meltdown91 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old May 19th, 2014, 08:24 PM   #2
cdw32
Senior Member
 
cdw32's Avatar
 
Join Date: 10-08-10
Location: Commerce MI
Posts: 474
iTrader: (8)
Mentioned: 0 Post(s)
Default

Damn, nice project! Wish I had the time to buy it and finish it.
cdw32 is offline   Reply With Quote
Old May 20th, 2014, 03:18 PM   #3
Meltdown91
Newbie
 
Meltdown91's Avatar
 
Join Date: 03-25-13
Location: Decatur, IN
Posts: 19
iTrader: (0)
Mentioned: 0 Post(s)
Default

Bump, Still for sale or trade! I'm only getting rid of it because I just bought a 94 YJ, and I am loosing interest.
Meltdown91 is offline   Reply With Quote
Old May 20th, 2014, 03:24 PM   #4
BigBlockBlazer
Axle breakin' 101
 
BigBlockBlazer's Avatar
 
Join Date: 10-08-08
Location: Traverse City, Mi
Posts: 2,340
iTrader: (12)
Mentioned: 0 Post(s)
Default

Does it have an interior? Seats, dash roll bar and what not?
BigBlockBlazer is offline   Reply With Quote
Old May 20th, 2014, 08:31 PM   #5
Meltdown91
Newbie
 
Meltdown91's Avatar
 
Join Date: 03-25-13
Location: Decatur, IN
Posts: 19
iTrader: (0)
Mentioned: 0 Post(s)
Default

Has two front seats, needs a passenger side riser and slider. Has all Dash panels, needs tach and speedo, stereo, speakers, and HVAC. Comes with column and steering wheel just not installed. I would say 85-90% is there or I have it somewhere

Oh and It does have the factory family cage
Meltdown91 is offline   Reply With Quote
Old May 20th, 2014, 08:32 PM   #6
Meltdown91
Newbie
 
Meltdown91's Avatar
 
Join Date: 03-25-13
Location: Decatur, IN
Posts: 19
iTrader: (0)
Mentioned: 0 Post(s)
Default

You can see more pics on my profile.
Meltdown91 is offline   Reply With Quote
Old May 21st, 2014, 10:36 PM   #7
Meltdown91
Newbie
 
Meltdown91's Avatar
 
Join Date: 03-25-13
Location: Decatur, IN
Posts: 19
iTrader: (0)
Mentioned: 0 Post(s)
Default

Still here 1500 bucks takes it... I want my night rod dang it lol
Meltdown91 is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > Great Lakes 4x4 Marketplace > Vehicles for sale

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:38 PM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.
Page generated in 0.14923 seconds with 43 queries