FS:FT: 93 turbo ranger project or rolling chassis. PRICE DROP! NEED GONE! - Great Lakes 4x4. The largest offroad forum in the Midwest

Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > Great Lakes 4x4 Marketplace > Vehicles for sale
GL4x4 Live! GL4x4 Casino

greatlakes4x4.com is the premier Great Lakes 4x4 Forum on the internet. Registered Users do not see the above ads.
Search
Reply
 
Thread Tools Search this Thread
Old September 25th, 2010, 06:48 PM   #1
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default FS:FT: 93 turbo ranger project or rolling chassis. PRICE DROP! NEED GONE!

i have a clean 93 ranger standard cab that originally came with a 4cyl. previous owner bolted on a turbo manifold from a merkur. Previous owner ran it with the turbo on the stock ecu and motor with only slightly larger injectors and cracked a piston. i pulled the motor and trans found a set of forged low compression pistons from a merkur and put them in with new bearings and reconditioned rods. been working to much lately to continue with the project so i'm just seeing if anyone would be interested in it. motor is out of truck right now, but is ready to start going back in. harness hasn't been modified yet so could easily return to stock at this point with a different motor. trans is a manual and worked well with the only issue being a bit of a sloppy shifter. rear axle has been swapped with an explorer axle with a lsd, rear discs, and 373 gears. the axle swapped dropped the rear 5-6 inches but the front hasn't been lowered yet. rear brakes need to be hooked up still. also still have stock axle. i have both the stock ecu and a LA3 ecu out of a turbo coupe. too finish this project you would need either a bigger maf sensor or a vam out of a turbo coupe, the harness needs to be repinned to work with the turbo ecu, and a tune put on the ecu is highly recomended.

if you have any questions just ask.

interested in possible trades for cars, trucks, atvs, motorcycles, tools, electronics, guns, etc... don't know what i'll want till i see it so offer them up.

asking $2000/obo for truck and all parts plus extras.
$1000 for everything. $500 for truck without motor and trans.

pics at this link. http://jamien.dnsalias.com/ranger

Last edited by Jbland83; January 28th, 2011 at 05:32 AM.
Jbland83 is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old September 30th, 2010, 09:45 PM   #2
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

i would be willing to sell just the body/chassis with no motor or trans if someone is interested, would make a good v8 swap.
Jbland83 is offline   Reply With Quote
Old October 6th, 2010, 07:40 PM   #3
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

tons of views but not a single offer, must not be a good time to sell a project.
Jbland83 is offline   Reply With Quote
Old October 19th, 2010, 12:24 PM   #4
SANDVIPR
Yeeeee Haaaaw!
 
SANDVIPR's Avatar
 
Join Date: 09-10-06
Location: Holland
Posts: 7,651
iTrader: (58)
Mentioned: 7 Post(s)
Default

Pics would help immensely.....
SANDVIPR is offline   Reply With Quote
Old October 19th, 2010, 03:47 PM   #5
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

there is a link to pics in the first post.
Jbland83 is offline   Reply With Quote
Old October 30th, 2010, 10:53 AM   #6
skife
Senior Member
 
skife's Avatar
 
Join Date: 02-12-07
Location: cedar springs mi
Posts: 5,121
iTrader: (5)
Mentioned: 0 Post(s)
Send a message via AIM to skife Send a message via MSN to skife
Default

sounds like the P/O ran it without a boost controller, 6 PSI max on stock non turbo pistons.
skife is offline   Reply With Quote
Old October 30th, 2010, 11:07 AM   #7
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

the P/O ran it at 10-15psi on a stock NA ecu with stock mustang injectors and the stock ranger 4cyl maf and a 190 fuel pump(which i haven't dropped the tank to verify so thats probably isn't true as well)
Jbland83 is offline   Reply With Quote
Old November 21st, 2010, 05:54 AM   #8
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

ttt - noone needs a good base for a v8 swap? how about something to get good mileage? i have everything to make it stock again.
Jbland83 is offline   Reply With Quote
Old November 25th, 2010, 02:54 PM   #9
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

turkey bump
Jbland83 is offline   Reply With Quote
Old November 25th, 2010, 04:22 PM   #10
Jeepaholc92
Senior Member
 
Jeepaholc92's Avatar
 
Join Date: 07-05-08
Location: Midland, MI
Posts: 662
iTrader: (1)
Mentioned: 0 Post(s)
Default

i've been wantin to do a project like this since i sold my 2.3 ranger but i sold that ranger to buy my new truck so i can't get this project off your hands FREE BUMP though, if by some dumb luck you still have this after i get my tax return i may have to look ya up.
Jeepaholc92 is offline   Reply With Quote
Old November 25th, 2010, 04:27 PM   #11
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

thanks! I'll keep bumping it up till it's gone so if you see it I still have it.
Jbland83 is offline   Reply With Quote
Old November 25th, 2010, 04:32 PM   #12
Jeepaholc92
Senior Member
 
Jeepaholc92's Avatar
 
Join Date: 07-05-08
Location: Midland, MI
Posts: 662
iTrader: (1)
Mentioned: 0 Post(s)
Default

thanks
Jeepaholc92 is offline   Reply With Quote
Old December 7th, 2010, 04:58 PM   #13
bigbchevy
missmrgreenagain
 
bigbchevy's Avatar
 
Join Date: 09-15-07
Location: fenton /hartland mi
Posts: 19,666
iTrader: (167)
Mentioned: 78 Post(s)
Default

pics please
__________________
H.o.r.e
(mr.green)So you are calling CC a liar?? Not a nice way to treat your bitch.
tube bending and gear installs pm me for info! gears installed for $150 and up per axle.
bigbchevy is online now   Reply With Quote
Old December 7th, 2010, 05:00 PM   #14
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

pics at this link. http://jamien.dnsalias.com/ranger
Jbland83 is offline   Reply With Quote
Old December 8th, 2010, 08:51 PM   #15
robn69
Senior Member
 
robn69's Avatar
 
Join Date: 01-29-09
Location: Pellston Mi
Posts: 823
iTrader: (8)
Mentioned: 0 Post(s)
Default

how much for just the body? No axles no frame just box cab and front clip?
robn69 is offline   Reply With Quote
Old December 9th, 2010, 04:01 AM   #16
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

$1000 obo for the body, makes a difference if i pull the body or you pull it. no delivery available.
Jbland83 is offline   Reply With Quote
Old January 28th, 2011, 01:33 AM   #17
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

Need room in the driveway, want this thing gone. $1000 for everything. $500 for truck without motor and trans.

Last edited by Jbland83; January 28th, 2011 at 01:51 AM.
Jbland83 is offline   Reply With Quote
Old January 29th, 2011, 03:06 PM   #18
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

Just picked up a new truck and need more room in the driveway. make me some offers! trades for four wheelers or snowmobiles possible!

Last edited by Jbland83; January 29th, 2011 at 03:10 PM.
Jbland83 is offline   Reply With Quote
Old February 23rd, 2011, 02:52 AM   #19
Jbland83
Senior Member
 
Join Date: 04-19-09
Location: Port Huron, MI
Posts: 122
iTrader: (2)
Mentioned: 0 Post(s)
Send a message via AIM to Jbland83 Send a message via Yahoo to Jbland83
Default

ttt
Jbland83 is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > Great Lakes 4x4 Marketplace > Vehicles for sale

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:51 PM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.
Page generated in 0.23727 seconds with 77 queries