Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > General Tech
GL4x4 Live! GL4x4 Casino







Search
Reply
 
Thread Tools
Old November 18th, 2008, 09:19 PM   #1
Plato2k5
In Da Faaaaaace!!!
 
Plato2k5's Avatar
 
Join Date: 12-25-05
Location: WMU Kzoo Mi / Livonia, MI
Posts: 5,416
iTrader: (17)
Mentioned: 0 Post(s)
Send a message via AIM to Plato2k5
Default 9" Moser shaft ID help ?? axle shaft lenght chart..??

Back when I was building up my rear 9" I ordered the wrong set of Moser shafts...one side is longer than the other. The place i order them through would not refund my money so they have been sitting in the attic for... 3 or so years. I had forgotten about them until recently and would like to sell them.

I seen there is a number stamped on the flange and it reads... 41405

I have done numerous searches on google and can't find anything.

Is there a chart somewhere that IDs the axle shafts by length??

I want to say they are for the EB broncos.
Plato2k5 is offline   Reply With Quote
Old November 18th, 2008, 09:51 PM   #2
Jeepaholic
Axle Guru Extraordinaire
 
Jeepaholic's Avatar
 
Join Date: 04-08-06
Location: Owosso
Posts: 7,289
iTrader: (116)
Mentioned: 2 Post(s)
Send a message via AIM to Jeepaholic Send a message via MSN to Jeepaholic
Default

If you post up the measurements I could check one of the EB 9" axles I have
Jeepaholic is offline   Reply With Quote
Old November 18th, 2008, 10:10 PM   #3
Plato2k5
In Da Faaaaaace!!!
 
Plato2k5's Avatar
 
Join Date: 12-25-05
Location: WMU Kzoo Mi / Livonia, MI
Posts: 5,416
iTrader: (17)
Mentioned: 0 Post(s)
Send a message via AIM to Plato2k5
Default

I can't find my tape measure rite now so tomorrow I will do that.

thank you !
Plato2k5 is offline   Reply With Quote
Old November 18th, 2008, 10:56 PM   #4
junk90xj
ALLPRO AUTO
 
junk90xj's Avatar
 
Join Date: 11-06-05
Location: lansing
Posts: 4,549
iTrader: (47)
Mentioned: 1 Post(s)
Default

if you call moser that number is their build number and they can tell you the application or if they are custom made.
__________________
http://www.apalansing.com/
junk90xj is offline   Reply With Quote
Old November 19th, 2008, 10:05 AM   #5
Plato2k5
In Da Faaaaaace!!!
 
Plato2k5's Avatar
 
Join Date: 12-25-05
Location: WMU Kzoo Mi / Livonia, MI
Posts: 5,416
iTrader: (17)
Mentioned: 0 Post(s)
Send a message via AIM to Plato2k5
Default

I guess i could do that :) thanks
Plato2k5 is offline   Reply With Quote
Old November 19th, 2008, 10:11 AM   #6
Fullsize4life
Kicking Cancers ASS
 
Fullsize4life's Avatar
 
Join Date: 07-25-06
Location: Hart, Mi (next to silver lake)
Posts: 18,757
iTrader: (7)
Mentioned: 0 Post(s)
Default

when i put moser shafts in the 9in I had in my bronco i ordered them equal length and they both fit in good. but i had a spool if that matters. Weird
Fullsize4life is offline   Reply With Quote
Old November 19th, 2008, 01:27 PM   #7
Plato2k5
In Da Faaaaaace!!!
 
Plato2k5's Avatar
 
Join Date: 12-25-05
Location: WMU Kzoo Mi / Livonia, MI
Posts: 5,416
iTrader: (17)
Mentioned: 0 Post(s)
Send a message via AIM to Plato2k5
Default

I resolved...well KillerB resolved the problem. He sent in my old shafts and had them matched. That was.... 3 years ago.

I just got off the phone with moser and the guy said that's the date code...which would make sense as it ends in 05.

So I took measurements of the shafts from the back of the flange to the end of the splines.

~29.25"

~27"
Plato2k5 is offline   Reply With Quote
Old November 19th, 2008, 01:33 PM   #8
nate4d
Gnarley Davidson
 
nate4d's Avatar
 
Join Date: 07-09-06
Location: Westland/Hale
Posts: 3,520
iTrader: (13)
Mentioned: 0 Post(s)
Send a message via AIM to nate4d
Default

how wide was the wms to wms? 31 spline?
nate4d is offline   Reply With Quote
Old November 19th, 2008, 01:56 PM   #9
Plato2k5
In Da Faaaaaace!!!
 
Plato2k5's Avatar
 
Join Date: 12-25-05
Location: WMU Kzoo Mi / Livonia, MI
Posts: 5,416
iTrader: (17)
Mentioned: 0 Post(s)
Send a message via AIM to Plato2k5
Default

I do not know the wms.... i know they are not for a 9" found under a big bronco or truck.
Plato2k5 is offline   Reply With Quote
Old November 19th, 2008, 03:10 PM   #10
Plato2k5
In Da Faaaaaace!!!
 
Plato2k5's Avatar
 
Join Date: 12-25-05
Location: WMU Kzoo Mi / Livonia, MI
Posts: 5,416
iTrader: (17)
Mentioned: 0 Post(s)
Send a message via AIM to Plato2k5
Default

Thanks 99grandtj!

Figured they are for 1966-75 Big Bearing bronco 9"
Plato2k5 is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > General Tech
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -5. The time now is 10:33 AM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.
Copyright 2005 - 2012 Cracker Enterprises - Powered by Linux
vB Ad Management by =RedTyger=
Page generated in 0.11519 seconds with 32 queries