Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > Great Lakes 4x4 Marketplace > Parts for sale
GL4x4 Live! GL4x4 Casino







Search
Reply
 
Thread Tools
Old July 17th, 2013, 06:20 PM   #1
KingCutlass
Classic ridin'
 
KingCutlass's Avatar
 
Join Date: 08-06-12
Location: Clarksville, MI
Posts: 64
iTrader: (0)
2 - Chevy NP205 T.C. 196 Ratio

I have two transfer cases that I need to get rid of considering that I'm not going to be needed them for spares. I'm going to keep my NP203 and rebuild it as necessary for now and maybe upgrade to a 208 in the future.

I have two of them, both seventies models. One is a 77, I think the other is a 76.

NP205 196 Ratio.

$75 Each.

Need funds for other parts, but willing to trade for other parts for 74-87 chevy:

*350 Truck headers (mine are bent from bad suspension smashing into it)
*Steering Shaft Extension (so I can finish my body lift)
*Decent plywood to repair the stepside bed.
*Decent Battery tray (mine is a rusted mess)
*Patch panels for floor or inner rockers (only bad rust spots on the truck)
*Matching set of manual door panels, any year or color, doesn't matter.
*Other stuff for 77 chevy 1/2 ton 4x4 stepside

I'm open to just about anything for this old truck. Throw me an offer, I'm very flexible on these.

Want them to go to someone who can use them.

Last edited by KingCutlass; July 17th, 2013 at 06:21 PM. Reason: edit to add
KingCutlass is offline   Reply With Quote
Old July 17th, 2013, 07:18 PM   #2
Merc09
Senior Member
 
Merc09's Avatar
 
Join Date: 11-30-12
Location: Pinckney/Mi
Posts: 156
iTrader: (0)
Willing to do a partial trade for another 203?
Merc09 is offline   Reply With Quote
Old July 17th, 2013, 08:06 PM   #3
KingCutlass
Classic ridin'
 
KingCutlass's Avatar
 
Join Date: 08-06-12
Location: Clarksville, MI
Posts: 64
iTrader: (0)
I'd like to get parts for the truck, but a partial trade would be good for a spare. What else did you have in mind? What condition is it in?

I'm ok with used parts for trade too depending on condition.
KingCutlass is offline   Reply With Quote
Old July 17th, 2013, 08:13 PM   #4
Merc09
Senior Member
 
Merc09's Avatar
 
Join Date: 11-30-12
Location: Pinckney/Mi
Posts: 156
iTrader: (0)
I was thinking 40$ and my 203 i was told it worked. A guy pulled it out of a running driving truck. Bolts to a th350 it needs to be power washed. Its pretty dirty. Where is clarksville in relation to pinckney?
Merc09 is offline   Reply With Quote
Old July 18th, 2013, 03:38 PM   #5
KingCutlass
Classic ridin'
 
KingCutlass's Avatar
 
Join Date: 08-06-12
Location: Clarksville, MI
Posts: 64
iTrader: (0)
Sounds good to me. Mine need to be cleaned too, but neighbor has power washer, so I should be able to clean them up.

Clarskville is half way between lansing and GR, just a couple miles south of I-96, about 20 mins NE of Hastings.

PM me and I can work out a time/place for you, or pictures if you want.
:)
KingCutlass is offline   Reply With Quote
Old August 28th, 2013, 02:33 AM   #6
KingCutlass
Classic ridin'
 
KingCutlass's Avatar
 
Join Date: 08-06-12
Location: Clarksville, MI
Posts: 64
iTrader: (0)
I need these gone, if not sold/traded for by this weekend then they are going in the scrap pile.
KingCutlass is offline   Reply With Quote
Old August 28th, 2013, 06:54 AM   #7
Bleay
sick of jackstand wheelin
 
Bleay's Avatar
 
Join Date: 11-18-05
Location: Clawson
Posts: 1,368
iTrader: (18)
Do you know what spline input these are? Or the trans that they were attached to?
Bleay is offline   Reply With Quote
Old August 28th, 2013, 09:19 PM   #8
BIG_BLAZER86
Senior Member
 
BIG_BLAZER86's Avatar
 
Join Date: 02-12-08
Location: Swanton Oh
Posts: 677
iTrader: (10)
And do you have the adapters
BIG_BLAZER86 is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > Great Lakes 4x4 Marketplace > Parts for sale
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -5. The time now is 03:16 AM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
Copyright 2005 - 2012 Cracker Enterprises - Powered by Linux
vB Ad Management by =RedTyger=
Page generated in 0.08493 seconds with 28 queries