Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > General Tech
GL4x4 Live! GL4x4 Casino







Search
Reply
 
Thread Tools
Old December 16th, 2011, 11:53 PM   #1
Plato2k5
In Da Faaaaaace!!!
 
Plato2k5's Avatar
 
Join Date: 12-25-05
Location: WMU Kzoo Mi / Livonia, MI
Posts: 5,393
iTrader: (17)
Send a message via AIM to Plato2k5
pads and rotors for wheeling

I need new pads for the rear of my jeep. The rotors are also warped so I may have them turned if they are within spec, or just buy new ones.

What do you use? Seems like there is a lot of warpage for the little driving I do. I'm sure there is a lot of heat build up when in 4 low at the dunes or on the trails?????

I had organic pads on the rear but they did horrible. I'd imagine a semi-metallic would be all that is needed for the rear??
Plato2k5 is offline   Reply With Quote
Old December 17th, 2011, 12:33 PM   #2
Kodiak450r
Keep on truckin
 
Kodiak450r's Avatar
 
Join Date: 11-14-07
Location: Waterford, MI
Posts: 5,900
iTrader: (19)
if its just a wheeler i would buy AZ pads and rotors. get the duralast as they have limited lifetime warranty. then when they go bad get them replaced for nothing. why spend alot of money on something you don't drive very much.
__________________
"I don't have pet peeves, i have major psychotic fucking hatreds" -George Carlin
Kodiak450r is offline   Reply With Quote
Old December 17th, 2011, 07:01 PM   #3
littletrucker
I'd hit that
 
littletrucker's Avatar
 
Join Date: 09-15-10
Location: Bear Lake 49614
Posts: 1,481
iTrader: (5)
I used the auto value parts master rotors in a 14 bolt disc brake swap for the back of my jeep (they have a lifetime warranty and all that) with wagner pads.. I also used the same thing when I replaced the pads/rotors on my dana 30... Just got done putting the brakes on the 60 front that is going in my jeep... parts master rotors wagner pads...


They work great, I dd it, wheel it. Haven't had a warped rotor yet. The price is great usually for both of those. If you are having trouble with warping I would check out your calipers, caliper slides and make sure everything moves freely

I also woudlnt even mess with turning rotors
littletrucker is offline   Reply With Quote
Old December 17th, 2011, 07:39 PM   #4
hobbyjeep
Senior Member
 
Join Date: 02-12-06
Location: commerce twp, mi
Posts: 150
iTrader: (0)
Bought last set of rotors/pads from Car Quest - wearing good. As said earlier check caliper slide pins and use toque wrench or torque sticks to tighten wheel lug nuts. DONT use the impact.
hobbyjeep is offline   Reply With Quote
Old December 17th, 2011, 11:00 PM   #5
Plato2k5
In Da Faaaaaace!!!
 
Plato2k5's Avatar
 
Join Date: 12-25-05
Location: WMU Kzoo Mi / Livonia, MI
Posts: 5,393
iTrader: (17)
Send a message via AIM to Plato2k5
Well I just went to Napa and bought their stuff.

However with my custom disc brake setup on my 9", I have ran into some issues. Seems as if the rotors I bought are thicker than what I originally had. This is causing the pads to get locked against the rotor causing it to not spin freely.

I need to re-work the brackets tomorrow and hopefully get everything working correctly.
Plato2k5 is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > General Tech
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -5. The time now is 04:24 PM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
Copyright 2005 - 2012 Cracker Enterprises - Powered by Linux
vB Ad Management by =RedTyger=
Page generated in 0.07417 seconds with 22 queries