Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Ford Tech
GL4x4 Live! GL4x4 Casino







Search
Reply
 
Thread Tools
Old June 29th, 2011, 12:35 PM   #1
Wehan
Senior Member
 
Wehan's Avatar
 
Join Date: 10-07-06
Location: Charlotte, MI
Posts: 2,290
iTrader: (25)
Mentioned: 2 Post(s)
Default pulling a 5.0 what not to forget

I am pulling a 302 (5.0 HO) from my buddies 90 Lincoln mark vii (7) to put in my jeep and i'm not sure what all i should pull other than the engine to make the swap easier (cheaper).
__________________

Last edited by Wehan; June 29th, 2011 at 12:56 PM.
Wehan is offline   Reply With Quote
Old June 29th, 2011, 12:38 PM   #2
masterbeatty
Senior Member
 
masterbeatty's Avatar
 
Join Date: 03-04-08
Location: my house
Posts: 4,143
iTrader: (17)
Mentioned: 4 Post(s)
Default

well are youu going efi or carb?
masterbeatty is offline   Reply With Quote
Old June 29th, 2011, 12:56 PM   #3
Wehan
Senior Member
 
Wehan's Avatar
 
Join Date: 10-07-06
Location: Charlotte, MI
Posts: 2,290
iTrader: (25)
Mentioned: 2 Post(s)
Default

going with the factory efi and 99% sure a manual trans
__________________
Wehan is offline   Reply With Quote
Old June 29th, 2011, 12:59 PM   #4
masterbeatty
Senior Member
 
masterbeatty's Avatar
 
Join Date: 03-04-08
Location: my house
Posts: 4,143
iTrader: (17)
Mentioned: 4 Post(s)
Default

pull it all. every sensor, wire, plug, any module everything you can. thats what i would do, really its always good to have to much when your doing an engine swap. if you want to get rid of it you can, but if you want it and dont have it you will need to buy it.
masterbeatty is offline   Reply With Quote
Old June 29th, 2011, 01:04 PM   #5
Wehan
Senior Member
 
Wehan's Avatar
 
Join Date: 10-07-06
Location: Charlotte, MI
Posts: 2,290
iTrader: (25)
Mentioned: 2 Post(s)
Default



this is it.
__________________
Wehan is offline   Reply With Quote
Old June 29th, 2011, 01:10 PM   #6
Wehan
Senior Member
 
Wehan's Avatar
 
Join Date: 10-07-06
Location: Charlotte, MI
Posts: 2,290
iTrader: (25)
Mentioned: 2 Post(s)
Default

well my buddy is scrapping the rest of the car and practically gave me the engine so i don't want to pull a whole bunch of unnecessary "weight" from the car so he can get top $ for it when he takes it in. i have the engine pulled and left all the wires i could attached to the engine and unplugged anything attached to the chassis because i plan to just get an aftermarket wire harness to mate it to my jeep when i get there. i dont think i want the ecm from the car because it is an auto trans ecm and from what i understand i will need one for a manual. on the other hand i could strip it and toss my 305 block in the trunk and call it good
__________________
Wehan is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Ford Tech
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -5. The time now is 02:34 AM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.
Copyright 2005 - 2012 Cracker Enterprises - Powered by Linux
vB Ad Management by =RedTyger=
Page generated in 0.22717 seconds with 24 queries