chevy dana 44 and corporate 10 - Great Lakes 4x4. The largest offroad forum in the Midwest

Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Axle Tech
GL4x4 Live! GL4x4 Casino

greatlakes4x4.com is the premier Great Lakes 4x4 Forum on the internet. Registered Users do not see the above ads.
Search
Reply
 
Thread Tools Search this Thread
Old January 14th, 2011, 08:08 AM   #1
84ChevyMuscle
BigBoysNeedBigToys
 
84ChevyMuscle's Avatar
 
Join Date: 12-27-08
Location: Saginaw, MI
Posts: 83
iTrader: (0)
Mentioned: 0 Post(s)
Send a message via AIM to 84ChevyMuscle
Default chevy dana 44 and corporate 10

i have a chevy corporate 10 bolt front axle 8 lug that im rebuilding and have a question. Will chevy dana 44 knuckles work on a chevy corporate 10? im kinda wanting to mix match them and run the drivers side dana 44 knuckle and then run the corp. knuckle on the passanger side, due to the condition of both.
84ChevyMuscle is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old January 14th, 2011, 04:27 PM   #2
ChevyRacer1981
Throw'in turtles........
 
ChevyRacer1981's Avatar
 
Join Date: 05-07-08
Location: Sagnasty / MI
Posts: 2,361
iTrader: (32)
Mentioned: 0 Post(s)
Default

I'm pretty sure everything from the knuckle out are interchangeable from both axles.
ChevyRacer1981 is offline   Reply With Quote
Old January 14th, 2011, 04:41 PM   #3
spr_chicken
Senior Member
 
spr_chicken's Avatar
 
Join Date: 05-12-08
Location: Grand Haven / Michigan
Posts: 1,116
iTrader: (9)
Mentioned: 0 Post(s)
Send a message via MSN to spr_chicken Send a message via Yahoo to spr_chicken
Default

As far as I know the only difference is the opening that the axle shaft goes through is bigger on the dana 44. I know you can put older 28 spline 10 bolt shafts in a dana 44. But the dana44 shafts will not go through the opening on a 10 bolt.
spr_chicken is offline   Reply With Quote
Old January 14th, 2011, 06:57 PM   #4
Ebrown
Senior Member
 
Ebrown's Avatar
 
Join Date: 06-28-06
Location: Saginaw Mich
Posts: 489
iTrader: (23)
Mentioned: 0 Post(s)
Default

You can run chevy dana 44 knuckles on a corp 10 bolt axle! Just watch out for the small / large bearing! But I have never heard of anyone wanting to mix them
Ebrown is offline   Reply With Quote
Old January 16th, 2011, 03:53 PM   #5
84ChevyMuscle
BigBoysNeedBigToys
 
84ChevyMuscle's Avatar
 
Join Date: 12-27-08
Location: Saginaw, MI
Posts: 83
iTrader: (0)
Mentioned: 0 Post(s)
Send a message via AIM to 84ChevyMuscle
Default

i dont really wanna interchange them but i have both pairs, its just the corporate 10 drivers side knuckle has the three studs missing for my steering arm so i was going to use the dana 44 drivers side knuckle
84ChevyMuscle is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Axle Tech

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:27 AM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.
Page generated in 0.11437 seconds with 36 queries