troubleshooting? - Great Lakes 4x4. The largest offroad forum in the Midwest

Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Toyota Tech
GL4x4 Live! GL4x4 Casino

greatlakes4x4.com is the premier Great Lakes 4x4 Forum on the internet. Registered Users do not see the above ads.
Search
Reply
 
Thread Tools Search this Thread
Old September 30th, 2010, 01:04 PM   #1
bighroder
Senior Member
 
bighroder's Avatar
 
Join Date: 01-27-10
Location: mid michigan
Posts: 155
iTrader: (1)
Mentioned: 0 Post(s)
Default troubleshooting?

I'm looking at buying an 87 4 runner soon the gas gauge doesn't work I would assume its the sending unit but I'm not firmilair with toyota so I figured I would ask in case it could be a common problem and just be a fuse or a short thanks for any help
bighroder is offline   Reply With Quote
Sponsored Links
Advertisement
 
Old September 30th, 2010, 06:45 PM   #2
ron86toy
R&V Ranger
 
ron86toy's Avatar
 
Join Date: 10-09-06
Location: Beaverton/ Edenville,mi
Posts: 1,033
iTrader: (10)
Mentioned: 1 Post(s)
Send a message via Yahoo to ron86toy
Default

more than likely the sending unit....15 bux @ yodajims + shipping
ron86toy is offline   Reply With Quote
Old September 30th, 2010, 07:03 PM   #3
Yota Bill
Senior Member
 
Join Date: 08-24-08
Location: Morrice, Mi
Posts: 3,229
iTrader: (11)
Mentioned: 0 Post(s)
Default

like any other problem, you can go by the "usualy is.." and the "most likely" answers, and start throwing money and parts at it till something sticks, or you could get a schematic, make a few tests, and buy the right part the first time and actually fix the problem.


going by the schematic at MeL, you will find 2 wires at the sender, 1 brn and one ylw/red. First test the brn wire for continuity to ground, and if that is good, then jump it to the ylw/red wire. Turn the key on, and with the wires jumped togethor, the guage should read full scale (pegged). If the guage does move, then remove and bench test/replace the sender.
If it does not, then you need to start testing at the guage itself. First off, get to the back of the guage, but leave it connected. Test for pos voltage at the red/wht wire (should be fine, since it feeds everything else as well) then test for ground at the brn wire (which is also the ground for the temp guage). If both of those are good, then test continuity across the ylw/red wire between the sender and the guage. If all tests till this point are good, assume the guage is the problem.
Yota Bill is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Toyota Tech

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:14 PM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.
Page generated in 0.10107 seconds with 30 queries