Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Axle Tech
GL4x4 Live! GL4x4 Casino







Search
Reply
 
Thread Tools
Old March 22nd, 2010, 11:19 PM   #41
MiNi Beast
Senior Member
 
MiNi Beast's Avatar
 
Join Date: 03-13-06
Location: Marquette, MI
Posts: 9,002
iTrader: (75)
Mentioned: 0 Post(s)
Default

Quote:
Originally Posted by lastmanstandin View Post
I believe I can install them correctly if I can get the information I need and take my time and do it right. Everyone has to learn sometime and I have alot of faith in myself. If I could get answers to my questions I could have it done by tomarrow....




To be honest with you it really doesn't matter if the whole jeep blew up, I have less then a thosand into it Not that I would want that to happen.

I understand that this is a job that requires alot of knowledge but it's by no means hard.........

I have no don't you could do it, anyone can do anything if they are so inclined to. However it is weather you have the proper tools to do the job. The general idea is to shim up the new gears with what came out shims, this will give you a good starting point. so this being said if you do not have a set of set up bearings(makes it so much easier to do at home) you need a press, well need a press anyway, but will need to press the bearings on and off which ever or however many times as needed. then remember that once you start to crush the sleeve you better be good other wise you will need a new one if you have to reset.
Possible search you tube for some vids on it i guess.
MiNi Beast is offline   Reply With Quote
Old March 22nd, 2010, 11:48 PM   #42
lastmanstandin
EvL 1
 
lastmanstandin's Avatar
 
Join Date: 08-27-09
Location: Coldwater Michigan
Posts: 3,566
iTrader: (30)
Mentioned: 0 Post(s)
Send a message via Yahoo to lastmanstandin
Default

Quote:
Originally Posted by MiNi Beast View Post
I have no don't you could do it, anyone can do anything if they are so inclined to. However it is weather you have the proper tools to do the job. The general idea is to shim up the new gears with what came out shims, this will give you a good starting point. so this being said if you do not have a set of set up bearings(makes it so much easier to do at home) you need a press, well need a press anyway, but will need to press the bearings on and off which ever or however many times as needed. then remember that once you start to crush the sleeve you better be good other wise you will need a new one if you have to reset.
Possible search you tube for some vids on it i guess.
Well I found this and I think I'm set. http://www.pirate4x4.com/tech/billavista/Gear_Setup/

I'm going to take the old bearings and make set up bearings out of the old ones. And this axle does not have a crush sleeve....I wish it did because it would make it easier. There is a couple things I don't understand but I'll ask those questions when I get to them.....I think I got this shit whipped..
lastmanstandin is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Axle Tech
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -5. The time now is 06:43 AM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Lite) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.
Copyright 2005 - 2012 Cracker Enterprises - Powered by Linux
vB Ad Management by =RedTyger=
Page generated in 0.07506 seconds with 16 queries