Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Rig Builds and Pics
GL4x4 Live! GL4x4 Casino

Rig Builds and Pics Introduce your rig or post a buildup here.







Search
Reply
 
Thread Tools
Old March 2nd, 2009, 12:29 PM   #1
CPK_Jim
Powder Coater
 
CPK_Jim's Avatar
 
Join Date: 11-14-08
Location: Kawkawlin/MI
Posts: 116
iTrader: (0)
Project Chevota

Well I started working on my truck again last wk. I have had this truck for almost 12 yrs, it was pretty close to stock when i bought it back in 97'. This will be the 3rd major build session for this truck. The first build I swapped out the drivetrain for a chevy vortec v6, 4l60e tranny, and a chevy tcase. I also installed a 5 inch superlift suspension kit and did some chevota type mods like chevy steering column, instrument cluster, bucket seats, center counsel and more. On the second build I installed a fiberglass box, .456 gears, locker in the rear, ditched the lift blocks for lift springs and painted the truck purple.

Here is a pic of it when i got it

This pic is the start of the first build on the truck.

This pic is just the rolling chasis

This pic is the donor truck were I got the motor and tranny from

This pic is setting the motor and tranny on the frame

This is a pic from the top with motor and tranny on the frame

Here is a pic of all the wiring I had to swap into the truck

Anyway just a start to my project post I will post more info and pics as I find them. As I mentioned this will be the 3rd build for the truck. These are pics from the first build. Hope you enjoy following the build.

Unfortunately I cannot find the pics from the second build, maybe i didnt take any, I cant remember. But heres a pic from silver lake last yr.


This time around Ive got some cool plans, for starters i was going to fix the hole I noticed developing in the floor of the cab, but decide to go a little further because the cab is getting pretty bad. So the plan is to rebuild the cab with a cage integrated into it. The cage inside the cab will attach to the cage I will be building over the bed, this should strengthen the truck immensely. I also plan to put some seating and padding in the bed when I do that cage, eventually I will make a soft top for that also.

Last yr I had to section the frame because it was really weak and cracked in the typical spot for these trucks. So this yr I want to build a whole new frame from scratch. Right now the plan is to do some sort of 4 link on bags in the rear and build a long travel independent setup in the front. PreRunner style, you dont see to many people doing this type of a build with these trucks, usually they ditch the IFS and put a straight axle in. But I like to be different and have always like the prerunner look so I am going that route. This should be interesting as I will be making as many of the parts as I can. There are some kits that you can buy but they are outrageously expensive.

And, yes I will be powder coating everything!! Ive even got some ideas on how to pc the frame. Its a little different process since the frame wont fit in my oven but i think we will figure it out, it will be beneficial to us if we can because I have to turn them away now.


although I'm not sure how much of it I will get to right now. Whatever I dont do now i will do in the fall.

Anyway heres some pics from the work last wk.



A little more progress, not as much as would like but things are a little crazy around here right now. We got the cab braced, holes cut in the floor with braces going down to the frame.



Next up, cut the floor out, remove cab mounts and start fabricating new cab mounts and roll cage.

I also have to fabricate a new tubing bender for this project, I have a game plan and material for that, so hopefully it wont hold me up to much.

It seems the further I get into this project the busier I get with pc work so i hope that doesnt slow me down too much i want this thing trail worthy again by the end of may. If I get held up on it too much I think I will hold off on the new frame and suspension till fall. Its too early to call right now, I'll decide when I get the cab done.

Jim
CPK_Jim is offline   Reply With Quote
Old March 3rd, 2009, 10:03 AM   #2
Tattood-Freak
Member
 
Tattood-Freak's Avatar
 
Join Date: 12-19-08
Location: bay city mi
Posts: 43
iTrader: (0)
nice build start jim. ill have to stop by and check it out.

shelby
Tattood-Freak is offline   Reply With Quote
Old March 3rd, 2009, 11:13 PM   #3
CPK_Jim
Powder Coater
 
CPK_Jim's Avatar
 
Join Date: 11-14-08
Location: Kawkawlin/MI
Posts: 116
iTrader: (0)
Well, got a little more done today thanks to T. We took the box off, cut out the floor, the rockers and most of the back wall. A little more hackin and it will be time to start putin the cab back together.







Jim
CPK_Jim is offline   Reply With Quote
Old June 30th, 2009, 11:09 PM   #4
CPK_Jim
Powder Coater
 
CPK_Jim's Avatar
 
Join Date: 11-14-08
Location: Kawkawlin/MI
Posts: 116
iTrader: (0)
So I figured its time I updated this. The cab reconstruction and roll cage took a little longer then I expected but turned out pretty well. heres a few pics of the past couple months.











Jim
CPK_Jim is offline   Reply With Quote
Old June 30th, 2009, 11:12 PM   #5
Pokerob
hug life
 
Pokerob's Avatar
 
Join Date: 10-25-06
Location: G-Rap, MI
Posts: 10,147
iTrader: (25)
nice job,

sweet toy
Pokerob is offline   Reply With Quote
Old June 30th, 2009, 11:53 PM   #6
mpsbvp
Hummer recovery team
 
mpsbvp's Avatar
 
Join Date: 02-04-06
Location: Clio MI
Posts: 2,086
iTrader: (8)
Send a message via AIM to mpsbvp Send a message via Yahoo to mpsbvp
Lookin great
mpsbvp is offline   Reply With Quote
Old August 1st, 2009, 08:40 PM   #7
Rattler
Home Sweet Homicide
 
Rattler's Avatar
 
Join Date: 04-17-06
Location: Bei City
Posts: 3,647
iTrader: (1)
Nice Toy. Keep up the good work.

Did it say something on the tailgate? I think I have seen it around Bay City before.
Rattler is offline   Reply With Quote
Old September 9th, 2009, 10:38 PM   #8
Tattood-Freak
Member
 
Tattood-Freak's Avatar
 
Join Date: 12-19-08
Location: bay city mi
Posts: 43
iTrader: (0)
ya it says chevota in yellow
Tattood-Freak is offline   Reply With Quote
Old September 9th, 2009, 10:51 PM   #9
wave_crusher
I'll Direc your TV
 
wave_crusher's Avatar
 
Join Date: 01-20-09
Location: Big Rapids, MI
Posts: 4,646
iTrader: (20)
Sweet looking truck

can't wait for more updates
wave_crusher is offline   Reply With Quote
Old September 9th, 2009, 11:04 PM   #10
forbyefore
.
 
forbyefore's Avatar
 
Join Date: 08-14-07
Location: Bay City/AuGres, MI
Posts: 1,431
iTrader: (0)
did I used to see this on wheeler rd/state st area?
forbyefore is online now   Reply With Quote
Old September 11th, 2009, 09:56 PM   #11
CPK_Jim
Powder Coater
 
CPK_Jim's Avatar
 
Join Date: 11-14-08
Location: Kawkawlin/MI
Posts: 116
iTrader: (0)
Quote:
Originally Posted by forbyefore View Post
did I used to see this on wheeler rd/state st area?
Yeah, I used to live there. That is where it turned purple, lol. It also got a few other mods at that time. Apparently I didnt take any pics on that build because I cant find any.

Yeah, I need to update this a little. Summer has been pretty busy so not alot of progress on the truck like I had hoped. I have been working on fabricating a custom dash. Ive spent way more time on it than I wanted to, but I think the end result will be worth it. I also got some 4 point harnesses and mounted the seats. I'll try and get some new pics up soon.

Jim
CPK_Jim is offline   Reply With Quote
Old September 12th, 2009, 09:39 AM   #12
Rattler
Home Sweet Homicide
 
Rattler's Avatar
 
Join Date: 04-17-06
Location: Bei City
Posts: 3,647
iTrader: (1)
Are you out on Parish? I have a co-worker that might want a bunch of quad parts coated.
Rattler is offline   Reply With Quote
Old September 12th, 2009, 06:29 PM   #13
CPK_Jim
Powder Coater
 
CPK_Jim's Avatar
 
Join Date: 11-14-08
Location: Kawkawlin/MI
Posts: 116
iTrader: (0)
Quote:
Originally Posted by Rattler View Post
Are you out on Parish? I have a co-worker that might want a bunch of quad parts coated.
240ft north of parish on 8 mile.
CPK_Jim is offline   Reply With Quote
Old September 12th, 2009, 06:44 PM   #14
Rattler
Home Sweet Homicide
 
Rattler's Avatar
 
Join Date: 04-17-06
Location: Bei City
Posts: 3,647
iTrader: (1)
I used to work for Randy Davies out on 7 Mile by Parish when he did auto upholestry at his parents many years ago.

I will pass some info on to my co-worker.
Rattler is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Rig Builds and Pics
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -5. The time now is 11:48 AM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
Copyright 2005 - 2012 Cracker Enterprises - Powered by Linux
vB Ad Management by =RedTyger=
Page generated in 0.16673 seconds with 40 queries