Go Back   Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Rig Builds and Pics
GL4x4 Live! GL4x4 Casino

Rig Builds and Pics Introduce your rig or post a buildup here.







Search
Reply
 
Thread Tools
Old March 1st, 2009, 09:48 AM   #81
liv2mx
i like jungle gym's.
 
liv2mx's Avatar
 
Join Date: 11-10-05
Location: silver lake
Posts: 11,134
iTrader: (4)
you better do some more bracing on your front upper link mount on the axle. you will bend that.looking good.
liv2mx is offline   Reply With Quote
Old March 1st, 2009, 11:07 AM   #82
feva4u
LCG
 
feva4u's Avatar
 
Join Date: 04-01-07
Location: Petoskey, MI
Posts: 10,092
iTrader: (11)
Yeah, it's not even tacked to the axle yet, I'm slow
feva4u is offline   Reply With Quote
Old March 7th, 2009, 08:43 PM   #83
feva4u
LCG
 
feva4u's Avatar
 
Join Date: 04-01-07
Location: Petoskey, MI
Posts: 10,092
iTrader: (11)
Paul came over today and was a huge help! We got the knuckles/TRE/Pitman arm reamed for TRE's. Also mocked up the steering, moved the steering box again and figured out where to put the track bar. I'm still mocking that in to make sure my upper is in the proper location.
Move the steering box another 3" forward, had to move the front bumper out an inch.

At 3.5" up travel. Should be able to get another .5-1.0" out of it.



I'll finish mocking up a trackbar tomorrow and cycle the suspension to check for clearance issues. I have to get DOM ordered this week. Thanks again Paul
feva4u is offline   Reply With Quote
Old March 8th, 2009, 06:41 AM   #84
VonDirt
Senior Member
 
VonDirt's Avatar
 
Join Date: 08-10-06
Location: west side michigan
Posts: 629
iTrader: (19)
looks good -

seem like its going to clear now ?

in terms of that frame mount, a gusset (as you mentioned) should do the trick. sometimes it can still deflect inward when its shock loaded in full droop, but if you can fit 45 worth of triangulation on both sides of the mount, and the bottom edge is to the box section of the frame, all the better
VonDirt is offline   Reply With Quote
Old March 8th, 2009, 08:22 AM   #85
KennyOffroad
Ridge Runners Offroad
 
KennyOffroad's Avatar
 
Join Date: 06-11-07
Location: South Haven, MI
Posts: 3,195
iTrader: (18)
Nice, looking good.








KennyOffroad is offline   Reply With Quote
Old March 8th, 2009, 01:37 PM   #86
Trailrig
Hoggin'-N-Boggin'
 
Trailrig's Avatar
 
Join Date: 02-12-06
Location: Flushing, MI
Posts: 1,815
iTrader: (24)
Send a message via AIM to Trailrig
i cut that crossmenber out completely and then put it in the frame, i suggest get it sitting down on the springs first and then decide if you are going to need to chop the frame, only reason i cut mine was because i wanted to keep it low, hindsight i think i would have just ran factory rear Tj springs with relocated buckets


http://www.misfitoffroad.com/phpbb/v...er=asc&start=0

all the way at the bottom
Trailrig is online now   Reply With Quote
Old March 9th, 2009, 01:15 PM   #87
feva4u
LCG
 
feva4u's Avatar
 
Join Date: 04-01-07
Location: Petoskey, MI
Posts: 10,092
iTrader: (11)
Quote:
Originally Posted by Trailrig View Post
.....i wanted to keep it low, hindsight i think i would have just ran factory rear Tj springs with relocated buckets
That's the plan for now, get suspension done and set it down on springs to get an idea of how it's going to sit. Ran into a snag.....well more of a choice really. I can run more lift to get the frame away from the axle or.......move the front of the frame up.

So with the trackbar mocked in place I no longer have any clearance issues between the upper mount and the oil pan. It did bring up some other "issues" though.

Testing suspension out




And the "issue". With belly @ 21" or whatever it's at with the current setup I'm going to be bottoming out bump stops on speed bumps . This is with pass side at ride height and 4" uptravel at drivers spring perch.

Flipped tie rod is into the track bar mount.


For the record, TJ's look retarded all low with big tires(maybe it's just the type of tire ) It's already been pointed out that it's on backwards......its so I can reverse out of the mud hole when I get stuck


feva4u is offline   Reply With Quote
Old March 9th, 2009, 01:30 PM   #88
JohnnyJ
Low Range Drifter
 
JohnnyJ's Avatar
 
Join Date: 11-09-05
Location: Hartland, MI
Posts: 5,926
iTrader: (37)
Quote:
Originally Posted by feva4u View Post
For the record, TJ's look retarded all low with big tires(maybe it's just the type of tire )
must be the tire.
__________________
Neither Skinny Nor Pretty DEAK Racing 4517 Ultra 4 Mod Class Rig
Barn sale! Check out what's left!
Surviving Project Car Hell - We have all been there
JohnnyJ is online now   Reply With Quote
Old March 9th, 2009, 02:17 PM   #89
feva4u
LCG
 
feva4u's Avatar
 
Join Date: 04-01-07
Location: Petoskey, MI
Posts: 10,092
iTrader: (11)
Quote:
Originally Posted by JohnnyJ View Post
Yep, for mockup though, I have the best tires no money can buy
feva4u is offline   Reply With Quote
Old March 10th, 2009, 07:02 PM   #90
pwilson22000
Senior Member
 
Join Date: 05-23-07
Location: Allegan, MI
Posts: 246
iTrader: (5)
Quote:
Originally Posted by feva4u View Post


And the "issue". With belly @ 21" or whatever it's at with the current setup I'm going to be bottoming out bump stops on speed bumps . This is with pass side at ride height and 4" uptravel at drivers spring perch.


I don't understand the 4 in. uptravel comment on the driver's side. Looks to me you have 1.5 in. X 2 + 3.5 in = 6.5 in uptravel at the tire with only driverside up. maybe i'm slow.
pwilson22000 is offline   Reply With Quote
Old March 10th, 2009, 07:40 PM   #91
feva4u
LCG
 
feva4u's Avatar
 
Join Date: 04-01-07
Location: Petoskey, MI
Posts: 10,092
iTrader: (11)
Quote:
Originally Posted by pwilson22000 View Post
I don't understand the 4 in. uptravel comment on the driver's side. Looks to me you have 1.5 in. X 2 + 3.5 in = 6.5 in uptravel at the tire with only driverside up. maybe i'm slow.
I have 4" between the jack stand and where the axle is at in that picture.....which is 6.5"at the tire. I believe uptravel is measured at the spring perch, could be wrong, I'm just a wannabe jeeper in way over my head Help me out people, should I have more travel than that at the tire or is that normal? Doesn't seem right to me.
feva4u is offline   Reply With Quote
Old March 11th, 2009, 05:08 AM   #92
VonDirt
Senior Member
 
VonDirt's Avatar
 
Join Date: 08-10-06
Location: west side michigan
Posts: 629
iTrader: (19)
Quote:
Originally Posted by feva4u View Post
I have 4" between the jack stand and where the axle is at in that picture.....which is 6.5"at the tire. I believe uptravel is measured at the spring perch, could be wrong, I'm just a wannabe jeeper in way over my head Help me out people, should I have more travel than that at the tire or is that normal? Doesn't seem right to me.

nah, your fine -

the difference between your wheel travel and the axle to bump travel is driven by how far out the bump stop is from the axle center line.

when one side is stuffed and the other droops, the axle pivots at that point and the stuffed side will continue to go up till the drooped side runs out of travel. if your bumps are out board it wont move much, if there more inboard it will move alot more - like a seesaw.

i dont think theres an exact right answer. youd just want to be sure everything clears and your shocks arent acting as the stops when its stuffed.
VonDirt is offline   Reply With Quote
Old March 11th, 2009, 09:04 AM   #93
jmdzuk
Senior Member
 
jmdzuk's Avatar
 
Join Date: 11-20-05
Location: Lowell MI
Posts: 2,566
iTrader: (13)
Glad to see this comming along.
Jeff
jmdzuk is offline   Reply With Quote
Old March 11th, 2009, 01:43 PM   #94
feva4u
LCG
 
feva4u's Avatar
 
Join Date: 04-01-07
Location: Petoskey, MI
Posts: 10,092
iTrader: (11)
Quote:
Originally Posted by jmdzuk View Post
Glad to see this comming along.
Jeff
Figured I owed you guys that for helping load it in sub-zero weather
feva4u is offline   Reply With Quote
Old March 11th, 2009, 08:48 PM   #95
feva4u
LCG
 
feva4u's Avatar
 
Join Date: 04-01-07
Location: Petoskey, MI
Posts: 10,092
iTrader: (11)
Quote:
Originally Posted by VonDirt View Post
nah, your fine -

the difference between your wheel travel and the axle to bump travel is driven by how far out the bump stop is from the axle center line.

when one side is stuffed and the other droops, the axle pivots at that point and the stuffed side will continue to go up till the drooped side runs out of travel. if your bumps are out board it wont move much, if there more inboard it will move alot more - like a seesaw.

i dont think theres an exact right answer. youd just want to be sure everything clears and your shocks arent acting as the stops when its stuffed.
I looked at it again tonight. When I combine putting the front back together, putting the other 2 holes back in for the steering box, and the fact that I need to move my spring perches......I'm pretty sure I'm going to cut and make my own front frame. This should allow me to run high steer in the front if I decide to go to it in the future. I have some more research to do on the grill/radiator section now.
I'm thinking something like this:

Off to do some research
feva4u is offline   Reply With Quote
Old March 12th, 2009, 10:08 PM   #96
feva4u
LCG
 
feva4u's Avatar
 
Join Date: 04-01-07
Location: Petoskey, MI
Posts: 10,092
iTrader: (11)
Got my shocks today. I didn't know the remote resis's were hard jointed, might not be a bad thing though. 15" travel at $62/shock to the door So is my build Xtreme now? The shocks say so (Edelbrock Xtreme travel 64210 model # fwiw)
feva4u is offline   Reply With Quote
Old March 13th, 2009, 04:03 AM   #97
VonDirt
Senior Member
 
VonDirt's Avatar
 
Join Date: 08-10-06
Location: west side michigan
Posts: 629
iTrader: (19)
Quote:
=feva4u;1576227]I'm pretty sure I'm going to cut and make my own front frame. This should allow me to run high steer in the front if I decide to go to it in the future. I have some more research to do on the grill/radiator section now.
sounds like a plan, that will help keep your ride height reasonable as well
VonDirt is offline   Reply With Quote
Old March 13th, 2009, 06:51 AM   #98
feva4u
LCG
 
feva4u's Avatar
 
Join Date: 04-01-07
Location: Petoskey, MI
Posts: 10,092
iTrader: (11)
Quote:
Originally Posted by VonDirt View Post
sounds like a plan, that will help keep your ride height reasonable as well
feva4u is offline   Reply With Quote
Old March 13th, 2009, 09:40 AM   #99
Jeepaholic
Axle Guru Extraordinaire
 
Jeepaholic's Avatar
 
Join Date: 04-08-06
Location: Owosso
Posts: 7,227
iTrader: (114)
Send a message via AIM to Jeepaholic Send a message via MSN to Jeepaholic
Been looking at the same thing with the frame, like how this guy did his;
http://pirate4x4.com/forum/showpost....76&postcount=5

Jeepaholic is offline   Reply With Quote
Old March 13th, 2009, 09:53 AM   #100
feva4u
LCG
 
feva4u's Avatar
 
Join Date: 04-01-07
Location: Petoskey, MI
Posts: 10,092
iTrader: (11)
Yeah, Jeepmann just finished doing his that way too
http://www.greatlakes4x4.com/showthr...02#post1579102
post 47
feva4u is offline   Reply With Quote
Reply
Great Lakes 4x4. The largest offroad forum in the Midwest > 4x4 Talk > Rig Builds and Pics
Tags
meballs

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump



All times are GMT -5. The time now is 06:16 AM.


Powered by: vBulletin, Copyright 2000 - 2012, Jelsoft Enterprises Ltd.
Copyright 2005 - 2012 Cracker Enterprises - Powered by Linux
vB Ad Management by =RedTyger=
Page generated in 0.23949 seconds with 53 queries