Great Lakes 4x4. The largest offroad forum in the Midwest - View Single Post - Mudd Warz - May 5th at Thunderbird Raceway
View Single Post
Old April 21st, 2012, 07:25 AM   #9
dirty1ton
Member
 
dirty1ton's Avatar
 
Join Date: 01-10-12
Location: twin lake
Posts: 30
iTrader: (2)
Mentioned: 0 Post(s)
Default

Here are the rules for the classes:


General Truck Rules

Solid tow out point (Each and every driver MUST pull a cable)
Helmets and seat belts required by all vehicle occupants
Fire Extinguisher on board
GOOD SPORTSMANSHIP is required or you will be asked to leave!
$20 one time entry fee per driver, per truck, per class


Classes and Rules


Class 1 36.5" DOT (non cut) tires and under
4x4 vehicles only-production type frames and suspension
Any motor drive train combination
Front of motor can not be behind center line of front axle
Body swaps allowed with motor in stock location of frame, axles within 6" of center of wheel well
Flat beds and gutting allowed, must maintain stock appearing bodies (not homemade)
Must have doors, hood, and firewall. Replacement fiberglass body or parts ok
Single carb, gasoline only, no nitrous
No aluminum heads or aluminum blocks permitted
Vehicles with factory support of cab cut, or glass removed, open or soft tops MUST have roll bar to the frame
Passengers allowed at the discretion of the track owner
Maximum engine size 514 cubic inches

Class 2 44" DOT (non cut) tires and under
Same rules as class 1

CLASSES 1 AND 2 ARE MEANT FOR LOWER BUDGET BEGINNERS, IF YOU SHOW UP WITH HIGH DOLLAR MOTOR TO RUN THOSE CLASSES, YOU WILL BE BUMPED UP TO CLASS 3 AND 4

Class 3 36.5" DOT (non cut) tires and under
​4x4 vehicles only-production type frames and suspension
Any motor and drive train combination
Body swaps allowed
Flat beds and gutting allowed, must maintain stock appearing bodies (not homemade)
Must have doors, hood, and firewall. Replacement fiberglass body or parts ok
Single carb, gasoline only, no nitrous
No aluminum blocks permitted
Vehicles with factory support of cab cut, or glass removed, open or soft tops MUST have roll bar to the frame
Aluminum heads allowed- conventional type only
Engine set back should be no more than 12" from centerline of axle to #1 spark plug
No aluminum hubs
No nitrogen shocks
No fiberglass or carbon fiber springs allowed
Passengers allowed at the discretion of the track owner
Wide five wheels are ok if they are used with an adapter, no wide five hubs

Class 4 44" DOT (non cut) tires and under
Same rules as class 3

Class 5​ 39.5" DOT tires and under
Cut DOT tires allowed
2"x3" square tube frames ok
4 link and other adjustable suspensions allowed
Engine must be in front of driver
Fiberglass bodies ok, no full fiberglass racing bodies
Max deck height Ford-10.320 GM-10.200 Chrysler-10.72
Alcohol through carb, no injection
Any enclosed transfer cases
Gutting allowed
Must be naturally aspirated
​Small blocks can run a 300 shot of nitrous, iron headed big blocks can run a 250 shot of nitrous
​FIRE SUITS REQUIRED!!!
Minimum four point harness
Roll cage requirements: 6 point minimum, with 4 points to the frame. .090 min thickness 1 5/8 min. on main support
Master kill switch within driver's reach with an exterior kill switch on right rear of vehicle
Maximum wheel base of 150"
Wide five wheels ok
NO PASSENGERS!!!

Class 6 54" DOT tires and under
Same rules as class 5

Class 7
ANYTHING GOES!!
Paddles and tractor tires ok
FIRE SUIT REQUIRED
NO PASSENGERS
Minimum 4 point harness
Roll cage requirements: 6 point minimum, with 4 points to the frame. .090 min thickness 1 5/8 min. on main support​
Master kill switch within driver's reach with an exterior kill switch on right rear of vehicle

This is our first year putting this on,so any suggestions would be helpful.
dirty1ton is offline   Reply With Quote
 
Page generated in 0.08546 seconds with 20 queries