Great Lakes 4x4. The largest offroad forum in the Midwest banner

reart steer cherokee buggy now parting out

7K views 36 replies 11 participants last post by  motox168 
#1 · (Edited)
no longer have time for the project and money is need else where so it must go. Feel free to make an offer. Money talks. Some trades considered pm me with what you have. $7500obo

chassis:
1996 cherokee classic
99 header panal.
tubed from seats back with 1.75x.120 and 1.75x.188 dom
unibody plated with 3/16 from coil bucket totube work
front inner fenders stretched to header panal
front stinger bumper
2x6 rockers lifted 4inches and boat sided to the frame
.25 aluminium boatsides and flat belly
custom flat belly xmember
shaved controll arm mounts
front tow hooks and sleaved inner frame
All body painted nissian 014 orange mist metalic
Suspension:
Double triangulated link front 4in up travel 10in down
-7.5 Rubicon express coilssold
-1.5x.25 dom upper links(painted to match body) with 3/4x3/4 Ruff stuff heims from hell
-2x.25 dom lower links(painted to match body) with 7/8x3/4 rudd stuff heims from hell.
-14in fox remote resivore shockssold
Double triangulate 4 link rear
-17 bilstein 9100 rock crawler remote resivore coil over.sold
-1.5x.25 dom upper links(painted to match body) with 3/4x3/4 Ruff stuff heims from hell
2x.25dom lower links(painted to match body) with 7/8x3/4 ruff stuff heims from hell

Axles
Front 78/79 hp 60
-3/8 upper link truss
-upgraded 80's brakes
-superior comp cut chromoly inners
-35 spline foote outers
-35spline warn premium lockouts
-ballistic coil brackets
-all 1/4 brackets
-1.75x.188 dom ram hoop filled with .25 plate
-ram mount ties into coil bucks and truss
-psc double ended 2x8 cylinder
-1.5x.25 tir rods with qs compoents 3/4x3/4 heims
-whole axle has been media blasted primed and painted
Rear axle 80s ford hp 60 housing
- short side has been lengthend by Rocksolid Performance
-78/79 cs and knuckles
-yukon king pin rebuild
-3/8ths truss
-2x8 se psc ramsold
-parts mike springless rear high steer arms
-1.5x.25dom tie rod with qs compents 3/4x3/4 heims
Drivetrain
4.0l with about 170k
-99 intake
-banks header
-flowmaster 40
-psc ct pump with pulleysold
-psc resovoersold
-port,polished, and shaved engine pro performance head
-airtex inline fuel pump
-16 drop sump rci fuel cellsold
-2yr old radiator
-power steering cooler
new water pump and t-stat
Aw4
-RAdesigns rt protype shifter(not made yet, I was testing for rory with old set up)
-new pump seal
-Np231j
Interior
-stock dash
-heater replaced with stainless switch panal
-heater on toggle
-push button start
-99 console
- no carpet
-jcw suspension seats
-console has frt% rear suck down,rear steer
-fuel pump cut off
Recovery
-champion 10k front winchsold
-new smittybuilt xrc8sold
-mile marker front 1.5k suckdown
-2 drings on front bumper
-1 dring insde stinger gusset
Other
-lift gate hydrolic rear steer controlls
-many extras and spares
-alluminum body panals
-rock lights
Needs
-gears(have front install)
-driveshafts
-rear axle shafts
-front u-joints
-front steering plumbed
-floor patched(some rust but had to cut for front links and tcases)
springs for coilovers
-exhuast Have a flowmaster 40 to go with
-Vehicle needs to be plumbed and rear brakes
-Front shock hoops
-starter
Here are a few older pics can get new pic for a serious buyer. I am sure there is mch I am forgetting.The jeep will come on roller ties and rims.










updated photos











 
See less See more
21
You have insufficient privileges to reply here.
Top