Parting out 94' Dodge 2500 (Cummins) Truck 160,000 miles

DodgeitRamit · December 27th, 2006, 02:19 PM

96' Dodge Ram parts

Steering box - 100
NP 241 T case - 200

96' 1/2 ton - Dana 44 front / 9.25 limited slip rear 3.55s everything is complete (plus spare wheel bearing still in box), brakes in exc condition, pulled to put in one tons - 550 obo

4 BFG ATs 35-12.5-15 on black aluminum 5x5.5 wheels, 1 almost new, 1 with good, 2 that were in front are uneven wore and not a lot of tread - 225obo

xtrm4xjp · December 27th, 2006, 04:41 PM

Not sure if he could do it right now but I know that Cooter was looking for a cummins motor for one of his projects. You may want to try PMing him.

Anders

Cooter · December 30th, 2006, 05:55 AM

Any pix of the engine? Does it run/drive now? Auto or manual trans?

Very interested for my '85 Dually Crew project...

rubicon 1 · December 30th, 2006, 08:22 AM

how much for the frame and rear springs?

Skooter_Built · December 30th, 2006, 09:44 AM

got a good rear bumper on it?

DodgeitRamit · December 30th, 2006, 10:58 AM

Front crossmembers were cut out to get the engine/trans out, front right mount is bent downward .......For the frame and rear springs pm me an offer. Rear bumper is no good hit in the middle. Have front bumper that has been painted black for 60 bucks. This truck will be going to the junkyard by the end of the week.

noodles · December 30th, 2006, 11:03 AM

Im very intrested pm sent.

DodgeitRamit · December 30th, 2006, 11:17 AM

Also selling the complete exhaust from flange to tailpipe 3" to 3 1/2" end I beleive

rubicon 1 · December 31st, 2006, 11:59 AM

the frame would have to be good enough and springs to use for a trailer project I am building.so with out looking at it ,i am guessing $110.00.thanks.

DodgeitRamit · December 31st, 2006, 03:23 PM

I can get that much from the junkyard ........ the frame is fine ....... it was hit in front and it just bent the tip of the right framerail downward with the body mount, well then I torched the crossmembers that were in front of the engine, other than that its a damn good frame and springs

rubicon 1 · December 31st, 2006, 05:15 PM

I pmed you with an offer as you wanted.I guess you didnt like my offer.Thus what do you want for the springs and the frame?I am trying to kept the cost down on this project.Also you are 4 to 4.5 hrs from me in driving time to pick this up.thanks.

Grizzy · January 11th, 2007, 04:24 PM

Give me a call about the exhaust and a (?) tailgate. I'm just over in KZoo.(231)631-4749

PavementPounder · January 11th, 2007, 07:19 PM

Quote:

Originally Posted by DodgeitRamit

NP 241 T case - 200

How many splines is the rear output?

DodgeitRamit · January 11th, 2007, 08:16 PM

Sorry I do not know off hand ....... part is not with me now can look this weekend. It was the same output splines as my 231 Tcase on my 96 half ton dodge if that helps